marble water spots to prevent and control disease

First, to prevent water spots, lesions

    Although the water to completely remove the marble disease is more difficult spots, but there are ways to completely avoid the occurrence of marble disease of water spots, specific methods are:

    1. In the use of special protective agent prior to installation and construction for protection against marble, and in particular the bottom surface of the marble protection.

    2. marble Installation of wet paste should be to minimize the water content in cement mortar and mortar in the amount, you can use semi-cement mortar.

    3. Scraping the underside of the marble as far as possible avoid the use of slurry and poured syrup on a semi-mortar way of the base paste marble.

    4. marble design and installation should be reserved for appropriate water vapor channel, after the installation should be maintained within the empty marble patchwork Chang, a week after the caulking treatment.

    5. Wet paste to install the marble should avoid getting wet or damp wash (especially the first two to three weeks after installation should be absolutely prohibited.)

    Second, the governance of water spot disease

    The reasons for the formation of water spots, and its composition is complex and marble under different circumstances, the reasons for the formation of water spots are also different. Water spots, called marble of cancer, to completely remove water spots, can be very difficult, the best way is prevention.

    1. Physical baking method

    This approach is the role of high temperature heat precipitation of alkali - silica bodies in the water, making it into a solid gel, and then use waterproofing agent for marble conservation. Because of this approach is only part of dealing with the surface of marble, so when alkali - silica gel into a solid body, the will immediately absorbed from the marble around the bottom and water, re-form water spots. Equipment is commonly used sunlamps or flamethrower.

    2. Chemical cleaning

    This approach is the use of marble scavengers to clean water spots, removal or destruction of marble plaque formation of alkali or alkaline water - silica gel (CSH), it loses moisture absorption capacity, so as to achieve the purpose of management of water spots.

    3. Cleaning baking synthesis method

    Use of marble scavengers remove water spots or water spots, damage to marble formation of alkali - silica gel (CSH), then dried baking marble in the water method.

    4. Brightening color method

    Brightening color method is to use enriched by the method of water marble plaque lesions in the lighter part of the marble color deepened to a level with the dark color of some of the same or close to the marble to achieve the beautiful decorative effect. Color method by Yan Yan is divided into color protection by law and common law by brilliant color, protective brightening the color palette method while adjusting the marble, the marble also play a protective role, common law only adjust the color brightening the color of the marble, can not afford protective effect.

    Currently, the spot for water treatment, the effect is still not ideal, that is what we need to be solved in an industry issue. In view of this, the prevention of water spots is particularly important.

    Third, water spots, a typical case of management

    There are two solutions to water treatment of plaque lesion, clear brilliant color reduction and growth method. Clear reduction method is to remove water spots, marble disease, restore the true colors of the marble, this method is to solve the problem of marble the best program of water spots, but also the most difficult program, due to the formation of marble disease, the reason is water spots complicated, especially direct contact with the bottom housing and water near the surface of the marble, may not be able to achieve fully satisfactory results. If the marble can not remove water spots, lesions of governance to achieve the purpose of reduction, the available method to eliminate the brightening spot disease of water produced by leaving the marble color, to enhance its decorative effect.

    1. Clear to restore the water treatment spot disease of marble

    marble Type: American Smooth Grey Granite Ma.

    Lesions: protection marble installation done before treatment, but some marble protectant brush brushing uneven and leakage, resulting in marble serious pollution of the water spots

    Material handling:

    1). Q-307S type of marble water spot removal agent.

    2). F-101R type of marble oil repellant.

    Construction method:

    1). In non-marble and marble do not clean the area protected.

    2). Clean up marble dust on the dirt and surface.

    3.) Scavenger with marble water spots were removed, A group of marble surface protectant.

    4.) Wring dry wet mop the marble surface of the dirt removal and residual marble group A scavenger water spots were.

    5). The marble water spots scavenger B: C = 1:1 Mix and brush on the marble surface, for 24 hours or more, the marble surface clean, natural dry 1-2 hours.

    6.) Repeat the above process (5), the color was pale marble surface, air dried 24 hours or more.

    7.) marble with a soft plastic film to cover a whole (including water spots around the lesion does not appear, part of marble), then gradually some of the plastic film off, the D group were down under the plastic film, cover with plastic film, with a soft brush across the plastic film were evenly brush the D group and then open the sealed tape or heavy plastic film around the seal 24 hours, thrown off all the cover on the marble, natural drying for 7 days.

    8). Repeat the process (7), air dried for 60 days, the marble surface water spots disappear.

    9.) marble with the F-101R model for oil repellant protective treatment.

    2. Protection brightening hair color treatment of the water surface of the granite plaque lesions

    marble Type: 603 # singeing plate produced in Fujian.

    Lesions: protection marble installation done before treatment, but some uneven marble and leakage brush brushing protectant, especially the side of marble protection in place, resulting in serious water marble plaque contamination.

    Material handling:

    1). F-848Y-type marble graced by Yan repellant.

    2). Q-308N-type granite renovation cleaning agent.

    Construction method:

    1.) Smooth marble in the surrounding area well protected with transparent tape.

    2). With a brush to F-848Y-type marble graced by Yan Protectant brushing the entire marble surface, the amount of 10m2 / L or so, light-colored marble parts appropriate to increase the amount of protective agent.

    3). To be fully protective agent into the marble house (at least 24 hours or more), check whether the marble's surface color is consistent, if there are color, light-colored parts of the marble and then painted a F-848Y-type protective marble graced by Yan agents, and allowed to fully penetrate inside the marble, so repeat until the marble's color completely eliminated.

    4.) Granite with a Q-308N-type cleaning agent will be refurbished marble surfaces clean.

    5). Again and again with water to wash the marble surface, and drag the water fully dry.